Tx 200 spread
Tx 200 spread
What power spread do your TX's have?
- TX22hunter
- Posts: 9
- Joined: Sun Feb 05, 2017 10:30 pm
Re: Tx 200 spread
My .22/HC runs 11.43-11.47fpe, couldn't tell you what that is in FPS though cos I forgot to check... ![Laughing :lol:](./images/smilies/icon_lol.gif)
![Laughing :lol:](./images/smilies/icon_lol.gif)
- fiestazetecmk2
- Posts: 117
- Joined: Mon Feb 16, 2015 11:35 pm
Re: Tx 200 spread
10.5 to 10.9.all day long on my chrono.rws superdomes. 22.with tinbum kit.
Tx200hc.22 .cs1000 stock,hawke varmint sf 6-24-44
Re: Tx 200 spread
May I ask you what tinbum bits you fitted? I'm of the understanding that the piston runs on delrin rings as standard, so I am wondering where the improvements have been made? Thinking of buying a .177 TX so your help will come in handy at some point.
Thanks
Bobby
Thanks
Bobby
Pain or damage don't end the world. Or despair or f...... beatings. The world ends when you're dead. Until then, you got more punishment in store. Stand it like a man, and give some back.
Albert Swearengen
Deadwood
Circa 1878
Albert Swearengen
Deadwood
Circa 1878
- TX22hunter
- Posts: 9
- Joined: Sun Feb 05, 2017 10:30 pm
Re: Tx 200 spread
dazzler wrote:May I ask you what tinbum bits you fitted? I'm of the understanding that the piston runs on delrin rings as standard, so I am wondering where the improvements have been made? Thinking of buying a .177 TX so your help will come in handy at some point.
Thanks
Bobby
Fiesta pm'd me by mistake I think...
It'll be a top hat/spring guide kit, there will be some slip washers and power washers in there as well...
- Barnydaddy
- Posts: 22
- Joined: Sat Feb 21, 2015 3:17 am
Re: Tx 200 spread
16.2 fpe.
8.64 H&N FTT at 915fps
8.64 H&N FTT at 915fps
Re: Tx 200 spread
Hi ! My Tx is relatively new and has been crono'd a 2 or 3 times between 10.3 and 10.6 which I felt was disappointing as it's sold as a Full Power rifle..... ok I know it won't be 12 !!! But I expected at least low 11's
At that time it had only had about 1000 pellets thru it .... Will it improve ???
Cheers Roj
At that time it had only had about 1000 pellets thru it .... Will it improve ???
Cheers Roj
- gary martin
- Posts: 815
- Joined: Thu Feb 19, 2015 8:21 pm
Re: Tx 200 spread
Roj 252 wrote:Hi ! My Tx is relatively new and has been crono'd a 2 or 3 times between 10.3 and 10.6 which I felt was disappointing as it's sold as a Full Power rifle..... ok I know it won't be 12 !!! But I expected at least low 11's
At that time it had only had about 1000 pellets thru it .... Will it improve ???
Cheers Roj
at1000 cycles, it has in all honesty most likely bedded in by now. is it a full length or HC model. a full length will make power easier. if you are so concerned, contact AA, tell them that you would like a little more, explain you understand the law and are not trying to achieve FAC levels, they will send you free of charge some power washers.
Re: Tx 200 spread
Oh Right !.... thanks very much for the info, its really appreciated. It is an HC so I am aware that they produce slightly lower figures. Obviously I need a margin to keep below the magic 12 No ! If they'll provide some washers that would be great as I have access to crono's at the club and my local dealer.
Thanks again !
Roj
Thanks again !
Roj
Re: Tx 200 spread
PS : Thanks Gary, before I do anything I'll get a few more Crono's done of the latest figures to be sure of the No's and then perhaps contact AA, as in the near future I'm planning on doing a bit of hunting, ..... as FPS means Prizes : -)
Cheers
Roj
Cheers
Roj
Who is online
Users browsing this forum: No registered users and 30 guests