AA s410 trigger/ charge advice needed

no avatar
Adamf410
Posts: 1
Joined: Sat Oct 29, 2016 5:19 am

AA s410 trigger/ charge advice needed

Sat Oct 29, 2016 7:34 pm

Hi all,
Joined today and need some advice please, picked up a second hand AA s410 today and the spring at the rear of the trigger blade is missing so floppy trigger, which spring do I need and is it straight forward to fit?
Plus noticed when I charged the gun that it leak air from around the valve/ adapter when it gets to about 155-160 bar. Is it just a case of replacing the rings?
Thanks in advance for any replays

no avatar
TenMetrePeter
Posts: 1043
Joined: Wed Jun 29, 2016 5:40 pm
Location: Luton Beds UK

Re: AA s410 trigger/ charge advice needed

Sat Oct 29, 2016 8:46 pm

http://www.bisley-uk.com/stockimages/do ... iagram.pdf

the diagram shows 2 trigger springs items 18 and 24.
Provided 18 is there, 24 is not needed if you want a light trigger which is only floppy when uncocked.
(18 is NOT a filling valve spring!)
buy spares at
http://airarmsspares.com/air-arms-spares/

no avatar
Roger5
Posts: 1071
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton middlesex

Re: AA s410 trigger/ charge advice needed

Sat Oct 29, 2016 11:00 pm

Adamf410 wrote:Hi all,
Joined today and need some advice please, picked up a second hand AA s410 today and the spring at the rear of the trigger blade is missing so floppy trigger, which spring do I need and is it straight forward to fit?
Plus noticed when I charged the gun that it leak air from around the valve/ adapter when it gets to about 155-160 bar. Is it just a case of replacing the rings?
Thanks in advance for any replays

If you want the spring at rear of trigger it is part no S311 trigger load spring, and fill valve o rings are S474 male connector o rings. Julian is the spares man on here, Rog

no avatar
TenMetrePeter
Posts: 1043
Joined: Wed Jun 29, 2016 5:40 pm
Location: Luton Beds UK

Re: AA s410 trigger/ charge advice needed

Sun Oct 30, 2016 8:04 am

yes sorry should have said that's Julians (bgaltd) spares website I posted but you can visit via this forum. send him a PM.

The Rothery Bisley site is wholesale only but they do good diagrams!

By the way you would need to have the original 410 trigger blade. If the previous owner fitted an adjustable blade like the Rowan one it may be too short to catch the second spring. For some reason AA omit the rear spring from all the MPRs that have an identical 3 sear trigger unit as 410 but shorter trigger blades. The spring hole is there but the spring would wriggle out. I think it is a lovely trigger without it anyway.

no avatar
Roger Wilco
Posts: 6
Joined: Sun Nov 06, 2016 8:00 pm

Re: AA s410 trigger/ charge advice needed

Sun Nov 06, 2016 8:04 pm

I cut the spring in a clipper lighter in half. It worked fine. Not the lighter though. :)

no avatar
woody2906
Posts: 37
Joined: Wed Oct 28, 2015 7:57 pm

Re: AA s410 trigger/ charge advice needed

Sun Nov 06, 2016 9:04 pm

Older S410s didn't have the little spring at the rear of the trigger, the trigger was floppy until cocked. The change over was about 2006 I believe about the same time as the T bar fill adapter. If the OP has the old style fill adapter then in all probability the trigger didn't have the spring.

Post Reply

Who is online

Users browsing this forum: No registered users and 22 guests