regulator who shall I get to fit it??

[Mapuia]

Is the installation of the regulator simple? Any other changes made besides drilling the breath hole and installing the reg.
im planning on doing the same with my s510 as well

[singlespeed]

Is the installation of the regulator simple? Any other changes made besides drilling the breath hole and installing the reg.
im planning on doing the same with my s510 as well

To run at a lower pressure, the transfer port from valve block, bolt housing and barrel will probably need enlarging.
Drill the air tube and wet n dry sand the area where the reg sits so the seals dont leak.
Its not essential, but recomended to lighten the striker (hammer), to reduce the chance of hammer bounce with revised spring settings.

I went with the upgraded kit that contains replacement springs, and outlet valve spring holder, drillbits for port and tube, as well as a screw for the transfer port adjustment.

[Mapuia]

Thanks for the reply. And what about the power adjuster? Does it still works?

[singlespeed]

Thanks for the reply. And what about the power adjuster? Does it still works?

Yes the power adjustment screw still works to restrict /open the transfer port for fine adjustment. The upgrade kit contains a cap head allen screw which can be cut down to suit. Although you could still use the original screw.

I have spent a while tweeking the firing pot spring tension adjustment so I can have the transfer port fully open, where my screw is trimmed down to the point its tightned fully but the port is unrestricted. That way, power cant be easily increased if the rifle gets checked

Hopefully away to get my dive bottle refilled today, so I'll be able to see what changes lightening the hammer has made. It sounds quieter which is probably due to the hammer not bouncing anymore, but ive not done a full graph since.

[Mapuia]

Thanks singlespeed. Thats what i was hoping to try out. Opening the transfer port fully and adjust the power through the spring tension of the firing pot. do post your full string. And any other changes if its not too much a problem.

[singlespeed]

Had my bottle refilled this morning, so straight into a full string through the Combro

.22 S410 with Lane regulator set to 80Bar and 3.5mm transfer port. Unsorted RWS Super H point pellets straight from the tin.
Pressure readings were just from the bottle gauge, so a bit subjective as to which exact shot equalled which pressure.

Shot FPS
1 596 190Bar
2 597
3 597
4 601
5 601
6 602
7 596
8 602 180Bar
9 599
10 600
11 601
12 597
13 602
14 604
15 597
16 600
17 597
18 600
19 594
20 600 160Bar
21 598
22 596
23 598
24 600
25 597
26 602
27 593
28 601
29 599
30 597
31 599
32 596
33 602
34 597
35 599
36 601
37 599 140Bar
38 597
39 597
40 600
41 600
42 603
43 604
44 597
45 597
46 601
47 599
48 609
49 597
50 598
51 602
52 599
53 602
54 601 120Bar
55 602
56 602
57 602
58 599
59 601
60 602
61 603
62 603
63 601
64 604
65 597
66 604
67 603
68 601
69 602
70 602
71 602 100Bar
72 605
73 606
74 602
75 603
76 602
77 602
78 601
79 600
80 598
81 600
82 602
83 601
84 601
85 599
86 600
87 599
88 597 80Bar
89 602
90 597
91 600
92 597
93 593
94 590
95 590
96 589
97 588
98 586
99 584
100 582
101 583
102 574
103 573
104 566 60Bar
105 569
106 562
107 559
108 558
109 577
110 549
111 548
112 545
113 540
114 540
115 534
116 528
117 523
118 519
119 509
120 506 40Bar
130 433
140 194 20Bar

Theres a couple of wayward shots, but I'm reasonably happy so far with 92 shots from a fill. Being as my rifle gives an awfull spread with the H point pellets, I didnt mind loosing a few extra magazines after the noticeable drop in power, just to see what happened.

[32:1]

In answer to your question, fit it yourself
I too fitted a lane reg, never even seen a pcp apart before

Ive tinkered with it and have now got an amazing 1fps average over ten shoots, and Ive seen that a good few times to, worst being 2.8fps

Go for it

Chris

[air gun]

a reg will improve any gun imo.