Tx 200 spread

no avatar
KeithS
Posts: 137
Joined: Mon Apr 13, 2015 6:58 pm

Tx 200 spread

Fri Feb 03, 2017 6:11 pm

What power spread do your TX's have?

no avatar
TX22hunter
Posts: 9
Joined: Sun Feb 05, 2017 10:30 pm

Re: Tx 200 spread

Tue Feb 07, 2017 10:56 pm

My .22/HC runs 11.43-11.47fpe, couldn't tell you what that is in FPS though cos I forgot to check... :lol:

no avatar
fiestazetecmk2
Posts: 117
Joined: Mon Feb 16, 2015 11:35 pm

Re: Tx 200 spread

Fri Feb 10, 2017 10:07 pm

10.5 to 10.9.all day long on my chrono.rws superdomes. 22.with tinbum kit.
Tx200hc.22 .cs1000 stock,hawke varmint sf 6-24-44

no avatar
dazzler
Posts: 61
Joined: Thu Jul 14, 2016 1:57 pm

Re: Tx 200 spread

Sat Feb 25, 2017 12:59 pm

May I ask you what tinbum bits you fitted? I'm of the understanding that the piston runs on delrin rings as standard, so I am wondering where the improvements have been made? Thinking of buying a .177 TX so your help will come in handy at some point.

Thanks

Bobby
Pain or damage don't end the world. Or despair or f...... beatings. The world ends when you're dead. Until then, you got more punishment in store. Stand it like a man, and give some back.

Albert Swearengen
Deadwood
Circa 1878

no avatar
TX22hunter
Posts: 9
Joined: Sun Feb 05, 2017 10:30 pm

Re: Tx 200 spread

Sun Mar 12, 2017 8:58 am

dazzler wrote:May I ask you what tinbum bits you fitted? I'm of the understanding that the piston runs on delrin rings as standard, so I am wondering where the improvements have been made? Thinking of buying a .177 TX so your help will come in handy at some point.

Thanks

Bobby


Fiesta pm'd me by mistake I think...

It'll be a top hat/spring guide kit, there will be some slip washers and power washers in there as well...

no avatar
Barnydaddy
Posts: 22
Joined: Sat Feb 21, 2015 3:17 am

Re: Tx 200 spread

Mon May 15, 2017 1:14 am

16.2 fpe.
8.64 H&N FTT at 915fps

no avatar
Roj 252
Posts: 13
Joined: Mon Aug 14, 2017 5:55 am

Re: Tx 200 spread

Sun Sep 03, 2017 7:33 am

Hi ! My Tx is relatively new and has been crono'd a 2 or 3 times between 10.3 and 10.6 which I felt was disappointing as it's sold as a Full Power rifle..... ok I know it won't be 12 !!! But I expected at least low 11's

At that time it had only had about 1000 pellets thru it .... Will it improve ???

Cheers Roj

no avatar
gary martin
Posts: 815
Joined: Thu Feb 19, 2015 8:21 pm

Re: Tx 200 spread

Sun Sep 03, 2017 1:43 pm

Roj 252 wrote:Hi ! My Tx is relatively new and has been crono'd a 2 or 3 times between 10.3 and 10.6 which I felt was disappointing as it's sold as a Full Power rifle..... ok I know it won't be 12 !!! But I expected at least low 11's

At that time it had only had about 1000 pellets thru it .... Will it improve ???

Cheers Roj


at1000 cycles, it has in all honesty most likely bedded in by now. is it a full length or HC model. a full length will make power easier. if you are so concerned, contact AA, tell them that you would like a little more, explain you understand the law and are not trying to achieve FAC levels, they will send you free of charge some power washers.

no avatar
Roj 252
Posts: 13
Joined: Mon Aug 14, 2017 5:55 am

Re: Tx 200 spread

Sun Sep 03, 2017 8:22 pm

Oh Right !.... thanks very much for the info, its really appreciated. It is an HC so I am aware that they produce slightly lower figures. Obviously I need a margin to keep below the magic 12 No ! If they'll provide some washers that would be great as I have access to crono's at the club and my local dealer.

Thanks again !
Roj

no avatar
Roj 252
Posts: 13
Joined: Mon Aug 14, 2017 5:55 am

Re: Tx 200 spread

Sun Sep 03, 2017 8:29 pm

PS : Thanks Gary, before I do anything I'll get a few more Crono's done of the latest figures to be sure of the No's and then perhaps contact AA, as in the near future I'm planning on doing a bit of hunting, ..... as FPS means Prizes : -)

Cheers
Roj

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests