Tx200hc rubber buffer tx227

User avatar
Targe
Posts: 41
Joined: Tue Jan 19, 2016 4:56 am

Tx200hc rubber buffer tx227

Mon Apr 18, 2016 8:06 pm

Heres how i fitted this little rubber buffer successful to my Tx200hc

1/ unscrew the end of the barrel (tx200hc) and poke out the remaining broken rubber stop, it just drops out the barrel end.
2/ I trimmed off the thin rubber tail leaving the thick stub still on and dropped the rubber buffer in boiling water, (watch those fingers) :)
Leave in there to soften for a couple of minutes
3/ then i just screwed it in with my thumb :) job done.

Ps: if you can't get it to fit in, Plan B :)
Get some hozelock o rings ebay item number 200345021257
And pop one or two onto the cocking lever

Hope this is of some use to someone ;)

Mic
Attachments
TX227.jpg
TX227.jpg (2.55 KiB) Viewed 4797 times

no avatar
Bosun
Posts: 105
Joined: Sat Feb 28, 2015 1:06 pm

Re: Tx200hc rubber buffer tx227

Tue Apr 26, 2016 11:59 am

Good advice. Even so, it can still be a b*"%^r to fit. Be careful if you use any sort of steel implement to help it on it's way. I slipped and scratched the underside of the barrel. Not seriously, but a bloody nuisance none the less.

Come on Air Arms, surely there has to be a better way? At least on the HC, something could perhaps be let into the cocking aid.
Air Arms ProSport 0.177 Walnut, MTC Mamba Lite 3-12x44
Air Arms TX200 HC 0.177 Walnut, MTC Mamba Lite 3-12x44
Weihrauch HW75 Pistol
Umarex Colt M1911A1 pellet Pistol
Umarex Beretta 92FS pellet Pistol
Swiss Arms P1911 BB Pistol

User avatar
Targe
Posts: 41
Joined: Tue Jan 19, 2016 4:56 am

Re: Tx200hc rubber buffer tx227

Thu Apr 28, 2016 4:34 pm

Lol the first one I tried to push in with a blunt plastic tooth pick :(
It end up with a damaged rubber buffer

But Heating the rubber up in boiling water works a treat ;)

Mic

no avatar
Dajo
Posts: 20
Joined: Mon Jul 27, 2015 9:14 pm

Re: Tx200hc rubber buffer tx227

Thu Apr 28, 2016 9:13 pm

A couple of "O" rings on the cocking aid of the HC works as good as anything else.


Dajo.

User avatar
moulindu
Posts: 31
Joined: Wed May 20, 2015 6:22 am

Re: Tx200hc rubber buffer tx227

Fri Apr 29, 2016 7:53 am

Targe wrote:Ps: if you can't get it to fit in, Plan B
Get some hozelock o rings ebay item number 200345021257
And pop one or two onto the cocking lever

Hope this is of some use to someone

Dajo wrote:A couple of "O" rings on the cocking aid of the HC works as good as anything else.



i used spare barrel seals to slide on to the 2 grooves on the cocking lever...works great.

User avatar
Blackbaronfish
Posts: 3690
Joined: Sun Feb 15, 2015 6:20 pm
Location: Nuneaton

Re: Tx200hc rubber buffer tx227

Fri Apr 29, 2016 9:51 am

Great tip and a good excuse to put the kettle on :mrgreen:

BBF
Did I mention that I'm the only one to have attended EVERY meet since we started

Post Reply

Who is online

Users browsing this forum: No registered users and 19 guests