Under performing S410 carbine

Under performing S410 carbine

Postby Paulgy80 » Mon Sep 11, 2017 8:55 pm

Dear All

I am a newby to PCP air rifles, got a Air Arms S410 carbine and have been using it for target shooting, recently purchased a chrono and was quite shocked to see the variance in velocities and what appears to be the low foot pound measurement.

The gun I acquired second hand from a retiring shooter, he had shot about 2 to 3000 pellets through it before he gave up. I am using a cylinder to recharge to 180bar it is a 177 and I am getting fps of 630 to 710 using a 8.4 grain JSB pellet.

So I guess the question is how to I get a more consistent fps and get it up to the sweet spot of around 11.5 foot pounds??? I dont want anything illegal or even borderline.

Look forward to any feedback

Cheers
Paul
Paulgy80
 
Posts: 4
Joined: Mon Sep 11, 2017 8:21 am

Re: Under performing S410 carbine

Postby Roger5 » Tue Sep 12, 2017 8:02 am

It might pay to fill in your location, there might be a member near to you who could help, without seeing the rifle it's hard to tell what the problem is. Probably only needs strip and clean. Rog
Roger5
 
Posts: 565
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton, Middlesex

Re: Under performing S410 carbine

Postby Paulgy80 » Tue Sep 12, 2017 2:45 pm

Many thanks for response Roger5

Can you or does anybody know where I can obtain a maintenance and set up manual for the rifle, I am more than set up for the job just need the sequence and set up data.

Cheers

Paul
Paulgy80
 
Posts: 4
Joined: Mon Sep 11, 2017 8:21 am

Re: Under performing S410 carbine

Postby Roger5 » Tue Sep 12, 2017 4:55 pm

Paulgy80 wrote:Many thanks for response Roger5

Can you or does anybody know where I can obtain a maintenance and set up manual for the rifle, I am more than set up for the job just need the sequence and set up data.

Cheers

Paul

Have a look-YouTube AirArms S410 Classic-stripdown guide. Hope that helps. Rog
Roger5
 
Posts: 565
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton, Middlesex

Re: Under performing S410 carbine

Postby Bullet » Tue Sep 12, 2017 6:31 pm

Bullet
 
Posts: 9
Joined: Sat Sep 09, 2017 9:54 pm

Re: Under performing S410 carbine

Postby Paulgy80 » Thu Sep 14, 2017 5:46 pm

Dear Bullet, boy that seems to have hit the mother load, will work my way through that thread. I am surprised nobody has written an overhaul manual for these great guns made in the UK
Paulgy80
 
Posts: 4
Joined: Mon Sep 11, 2017 8:21 am

Re: Under performing S410 carbine

Postby Roger5 » Thu Sep 14, 2017 8:58 pm

To be honest, once the anti tamper is out they are pretty easy to work on, which is the reason I love them, they don't really have any bad problems, some of the S510s with the shrouded barrels can be a pain, pellet clipping being the main problem, but apart from that, they are pretty much bomb proof, 50yd bunnys ok with .177 and my .22 gets used out in the woods, you can pay a lot more for a rifle, but there really is no need, the S400/410/510 can do it all. Just been told off for leaving the little cz200 out, another brilliant piece of kit. Rog
Roger5
 
Posts: 565
Joined: Sat Jul 25, 2015 8:04 am
Location: Hampton, Middlesex

Re: Under performing S410 carbine

Postby Bullet » Sat Sep 16, 2017 7:45 am

Ive just fixed mine for £41-85 it was only kicking out 6ft/lb but with a new striiker and striker rod and spring and new striker bushes a couple of seals its back up to the legal 11ft/lb + yes you can polish the rod etc but if it has marks on just buy new
Bullet
 
Posts: 9
Joined: Sat Sep 09, 2017 9:54 pm

Re: Under performing S410 carbine

Postby Paulgy80 » Tue Sep 19, 2017 7:24 pm

Dear Bullet, boy that seems to have hit the mother load, will work my way through that thread. I am surprised nobody has written an overhaul manual for these great guns made in the UK
Paulgy80
 
Posts: 4
Joined: Mon Sep 11, 2017 8:21 am

Re: Under performing S410 carbine

Postby TenMetrePeter » Tue Sep 19, 2017 10:04 pm

Youtube is the new user manual medium.
S400 MPR Precision 10m.
My Youtube
User avatar
TenMetrePeter
 
Posts: 506
Joined: Wed Jun 29, 2016 5:40 pm
Location: Luton England NOT EU


Return to TECHNICAL

Who is online

Users browsing this forum: No registered users and 2 guests

cron